济南罗杰杜彼手表售后服务

　　精时恒达手表全国连锁维修点(请选择您就近的维修点咨询售后事宜)

　　北京精时恒达手表售后维修服务地址：北京西单大悦城写字楼7层702室

　　上海精时恒达手表售后维修服务地址：上海黄浦区南京东路置地广场9楼918室

　　广州精时恒达手表售后维修服务地址：广州市天河区体育西路103号维多利广场写字楼A座26层

　　深圳精时恒达手表售后维修服务地址：深圳市罗湖区深南东路5002号地王大厦(信兴广场)25层2510室

　　成都精时恒达手表售后维修服务地址：成都市锦江区天府广场百扬大厦21层2107室

　　杭州精时恒达手表售后维修服务地址：杭州大厦C座坤和中心30层3006室

　　济南精时恒达手表售后维修服务地址：济南市历下区泉城路180号齐鲁国际大厦B座10楼-1005室

　　沈阳精时恒达手表售后维修服务地址：沈阳市和平区中华路69-1号富丽华国际商务中心9楼903室

　　南京精时恒达手表售后维修服务地址：南京市南京国际金融中心写字楼10楼H

　　太原精时恒达手表售后维修服务地址：太原迎泽区柳巷南路钟鼓楼街15号

　　江西精时恒达手表售后维修服务地址：江西省南昌市东湖区胜利路步行街32号裕泰福珠宝二楼

　　天津精时恒达手表售后维修服务地址：天津市和平区南京路219号天津中心写字楼9楼

　　广西精时恒达手表售后维修服务地址：南宁市青秀区金湖路59号地王大厦12楼。(写字楼周六周日需要在前台登记才能按电梯)

　　河南精时恒达手表售后维修服务地址：郑州市金水区花园路39号国贸中心招银大厦14层1406室

　　【精时恒达手表售后维修中心门店图】

　　【图为：手表抛光工作台】

　　【上图为：手表做真空、压缩、冷凝及防水测试的设备】

　　当把手表维修这些问题都检查出来并加以排除后，再用测试机测试，测得各项数据平均值都在标准值内，即表示手表可以准确的运行了，**后若是自动上炼表，可再放于多方位测试机上测时，了解在多方位测试下，时间是否运转精准，并了解表的自动上炼是否没有问题。一切程序都通过后，就大功告成了。

　　我们将有关与手表走时不准的解决方法稍加整理，发现大致上可归结出以下九种原因，零件缺乏时再做修复。

　　手表走时不准测试

　　(1)如遇正面反面3点方向时间据差距太大(方向差)。方法：用摆轮平衡器测试，藉由摆轮旋转来得知摆轮圆径是否均重，如有某方位较重将减轻重量，来达到摆轮圆径均重。

　　(2)摆轮车心太短小油盘会碰到马仔嘴，造成摆轮不平衡。方法：换车心或摆轮整组换掉，或将受石反面装。

　　(3)小油盘松动导致测试值无法稳定。方法：将小油盘取下加以固定(切勿用胶水固定)。

　　(4)车心如遇异常磨损造成铁锤型(头大身细)导致摆轮不平衡。方法：修饰车心，修饰完要将车心打亮(要注意不能导致车心太细)。

　　(5)洗油后轮系如无法适当释放力道原因:1.干净度不够2.齿轮上下间隙太大3.齿轮芯磨损导致左右间隙太大4.上下铜质座磨损导致 左右间隙太大。

　　方法：1.重新清洗2.调整上下宝石座3.换齿轮4.将磨损部份修复。

　　(6)游丝乱掉原因：1.外力影响2.受石油外漏导致游丝沾粘住3.游丝受磁。方法：1.调整游丝2.清洗游丝3.退磁。

　　(7)发条无法正常释放力道原因：1.油太干2.生锈3.弹性疲乏。方法：1. 清洗干净重新加油2.将发条取出重新打亮再上油3.换新发条。

　　(8)自动机芯发条打滑。方法：取出发条，将发条盒壁磨粗或是用特制的发条油。

　　(9)马仔脚与五番车接合点如有误差导致力道不够，使摆轮无法正常运转。方法：调整马仔脚到适当位置。

　　以上这些问题都检查出来并加以排除后，再用测试机测试，测得各项数据平均值都在标准值内，即表示手表可以准确的运行了，**后若是自动上炼表，可再放于多方位测试机上测时，了解在多方位测试下，时间是否运转精准，并了解表的自动上炼是否没有问题。一切程序都通过后，就大功告成了。

watch repair these problems are checked out and ruled out, and then the test machine test, the average value of all measured data in standard value, that watch can accurate operation, finally if the automatic mixing table, can be placed in the multi position test machine measurement, understanding in many aspects the test time is running, accurate, and understand the table of the automatic mixing is no problem. All procedures are passed, will be accomplished.

we will be related to the watch travel time are not allowed to solve the solution with a little finishing, found generally can be attributed to the following nine reasons, when the lack of parts to do repair.

watch travel time is not allowed to test

(1) in the case of 3 points in the direction of the negative side of the gap is too large (Fang Xiangcha). Methods: the test wheel balancer, balance wheel rotation by that wheel diameter are heavy, if there is a range of heavier will reduce weight, to achieve a circular size weight.

(2) a car was too short encounter by pan mouth, caused by wheel imbalance. Methods: to balance the whole group of heart or replaced, or will be affected by the negative charge of stone.

(3) value to the small oil pan due to loose stability test. Methods: take the small oil pan to be fixed (not fixed with glue).

(4) in case of abnormal heart car caused by wear hammer type (head body fine) leads to imbalance of balance. Method: modify the heart of the car, finishing to the heart of the car (to pay attention can not lead to the heart of the car is too thin).

(5) after the train if not properly wash oil release force reasons: 1 clean enough 2 gear on 3 core gear gap is too large due to wear around the gap is too large 4 seat wear under copper lead around the gap is too large.

method: 1 to clean the 2 adjustment of the gem seat 3 change gear 4 will wear part of the repair.

(6): 1 gossamer mess force affected 2 oil leakage caused by the magnetic dip stick 3 gossamer gossamer. Methods: 1 adjust the hairspring 2 cleaning hairspring 3 demagnetization.

(7) cannot be released spring force: 1 oil too dry 2 rusty 3 elastic fatigue. Methods: 1 clean gas will take 2 to spring to play again 3 new spring light oil.

(8) automatic movement of the spring slip. Method: take out the spring, grind the box wall or use a special spring oil.

(9) followed by feet and five joints such as some car errors leading to a lack of strength, not the normal operation. Methods: by foot to the proper position adjustment.

these questions are checked out and ruled out, and then the test machine test, the average value of all measured data in standard value, that watch can accurate operation, finally if the automatic mixing table, can be placed in the multi position test machine test, understand the multi-faceted test. Time is running precision, and understand the table of the automatic mixing is no problem. All procedures are passed, will be accomplished.

精时恒达全国连锁维修：400-875-1181全国百家连锁，**名表维修**，服务地区：北京 、上海、广州、杭州、深圳、沈阳、南京、太原、成都、 天津、 南昌 、武汉 、、等等