济南卡地亚（CARTIER）手表授权售后【**指定济南售后维修保养】

　　精时恒达手表全国连锁维修点(请选择您就近的维修点咨询售后事宜)

　　精时恒达名表连公司成立于2001年是一家专注于手表维修的现代化大型服务型企业。公司总部位于北京，在全国各大中型城市设有维修服务中心，形成了庞大的手表售后维修服务网络，为广大消费者提供方便、快捷的手表维修服务!

　　【精时恒达手表售后维修中心门店图】

　　【图为：手表抛光工作台】

　　【上图为：手表做真空、压缩、冷凝及防水测试的设备】

　　手表指针掉了是比较常见的，尤其是手表秒针掉了。手表在受到撞击的情况下很容易出现手表指针脱落的情况。那么出现这种情况应该怎么办?

　　下面我们一起来听一听精时恒达专业的修表师傅是怎么说的。

　　1、不要在22点-2点，(部分手表20点-4点)去调整日期，容易造成手表的损坏和日历跳转的不正确。

　　2、为了延长手表使用寿命，很多手表都采用慢跳的方式也就是在午夜前后时间段逐步跳转，一般在凌晨2 点前跳转完是正常的，部分手表至凌晨4点完成。

　　3、出现白天跳日历的情况可以进行调整—如果发现日历是在白天中午左右跳转的,一般是手表的时间快、慢了12小时,比如现在实际是上午11 点，手表却是前一天下午11点, 只需要将手表时针加拨一圈,即把下午改成上午。这种情况是比较普遍的，大概有50%的几率。

　　4、一般手表在时间调整都需要顺时针拨，不要逆时针拨。逆时针拨手表很容易造成手表指针指向的偏差(石英二针式应逆时针拨)。要特别的注意，如果是左手佩戴，用右手调节的话，往前转动就是顺时针。

　　5、手表的款式不同调整的方式也不一样，但在调整带日历功能的手表时都需要考虑上午和下午的因素。

　　手表的星期和日历调节注意事项

　　1、星期和日历不能在21点到凌晨3点调，这样很伤表。日历的跳动是齿轮带动的，一般都是慢慢跳的。

　　2、手表和石英表不同，石英表的日期和星期都是在零点跳字的，这种**度只在电子表里出现。指针手表没有那么**的，可能提前或延后，这是因为日期和星期都是一个轮圈来推动的。

　　3、如果同时跳字的话，驱动力就要求很大了。所以分开来换，一般星期变动会在日期的变动之后的半个到几个小时内跳过。

　　4、如果遇到手表的日期中午11点、12点、下午1点才跳。不要着急，只要把时针按顺时针方向把转一周,再重新调整日期就可以了。

　　5、中间的那个调整钮共两挡，**挡是调整日期，第两挡是调整时间的。**挡调整时，往后旋转是调日期，往前旋转是调星期。如果表本身没有星期显示的话，就不用星期设置。

　　Watch pointer off is relatively common, especially watch second hand off. Watch in the case of the impact of the case is very easy to watch the fall off the watch. So what should happen to this situation?

　　Let's listen ryham professional repair master table is how to say.

　　1, do not in the 22 point -2 point, (part of the watch 20 point -4 points) to adjust the date, easy to cause the damage of the watch and calendar jump is not correct.

　　2, in order to prolong the service life of the watch, many watches are using slow hop mode is in the middle of the night time gradually jump, usually at 2 in the morning before the end of the jump is normal, part of a watch to 4 a.m. to complete.

　　3, the day the jump calendar can be adjusted if the calendar is found in the daytime jump around noon, watch the time is generally slow and fast for 12 hours, for example, is now 11 in the morning, the day watch is before 11 in the afternoon, only need to watch dial clockwise in a circle, that afternoon into the morning. This situation is more common, there are about 50% probability.

　　4, the general watch in time adjustment need to dial clockwise, do not reverse the clock dial. The counter clockwise dial watch is easy to cause the deviation of the watch pointer (quartz two pin type should be counter clockwise). To pay special attention to, if it is left hand to wear, with the right hand to adjust, then the forward rotation is clockwise.

　　5, watches the style of different adjustment is not the same, but in the adjustment of the calendar function of the watch needs to consider the morning and afternoon.

　　Watch week and calendar adjustment notes

　　1, the week and the calendar can not be in 21 to 3 am, so very hurt table. The beating of the calendar is a gear drive, usually a slow jump.

　　2, watches and quartz watch, quartz watch the date and the week is in the zero jump word, this accuracy is only in the electronic table. Pointer watch not so accurate, may advance or delay, this is because the day of the week is a wheel driven.

　　3, if the words at the same time, the driving force on the requirements of a large. So separate to change, the general week changes in the date of the change in the half to a few hours after the jump.

　　4, if you encounter watches the date of 11 noon, 12 points, 1 points in the afternoon before the jump. Do not worry, as long as the clockwise direction to turn around a week, and then re adjust the date can be.

　　5, the middle of the adjustment button is a total of two blocks, the first block is to adjust the date, the second block is to adjust the time. When the first gear is adjusted, the rotation of the rotation is the date, and the rotation is the week. If the table itself does not show up on a week, you do not have to set up a week.

精时恒达全国连锁维修：400-875-1181全国百家连锁，**名表维修**，服务地区：北京 、上海、广州、杭州、深圳、沈阳、南京、太原、成都、 天津、 南昌 、武汉 、、等等